HVAC Repair & Electrical Services in Okemos, MI

Completed comprehensive tune-up and maintenance service on a 3-year-old Lennox WT 10-2027 HVAC system with a 2022 compressor. Inspected and documented pleated air filter condition within housing assembly, verified proper installation and airflow capacity. Examined blower assembly components, copper refrigerant lines, and electrical connections including wiring harness integrity. System confirmed operational and functioning within normal parameters upon completion of preventive maintenance procedures.

Completed annual heating maintenance on residential forced-air furnace system. Performed comprehensive inspection of all internal components including blower motor assembly, draft inducer, gas valve, heat exchanger, burner assembly, electrical connections, and control board. Verified proper operation of all safety systems, checked wiring harnesses for secure connections, and confirmed unit specifications against manufacturer labels. All components found in working condition with no repairs needed at this time.

# HVAC Maintenance - AHM Completed Performed annual heating maintenance on air handler unit. Discovered and documented significant frost accumulation on evaporator coils indicating potential refrigerant issue, airflow restriction, or temperature control malfunction. Inspected control board, electrical connections, and wiring harness - all components found secure with proper terminations. Replaced air filter as part of routine maintenance protocol. System requires follow-up diagnostic evaluation to address abnormal frost buildup and restore proper operation.

Completed annual heating and cooling maintenance on HVAC system. Performed comprehensive inspection of heating components, replaced air filters and evaporator pads, and verified proper operation of Honeywell Home thermostat with confirmed temperature setpoints of 67°F heat and 77°F cool. All equipment operating within normal parameters.

Performed comprehensive preventive maintenance on a 2-year-old Lennox central air conditioning system. Completed full system inspection including condenser unit exterior examination, verified proper refrigerant line connections, and assessed electrical disconnect operation. Noted minor debris accumulation and moss growth on concrete pad around outdoor unit, which is typical for the system's location against exterior wall. System operating within normal parameters with no deficiencies requiring immediate attention at time of service.

Completed comprehensive tune-up and maintenance on residential gas furnace system. Customer reported fan operating louder than normal; performed thorough inspection of blower motor assembly, verified proper mounting and bearing operation. Conducted full system diagnostics including testing gas valve operation, inspecting heat exchanger, verifying electrical connections and control board functionality, and checking all safety controls. Cleaned blower wheel and housing, lubricated motor bearings as needed, and tightened all mounting hardware to reduce operational noise. Verified proper airflow, tested ignition sequence, confirmed venting and condensate drainage systems operating correctly. System restored to normal operating parameters with reduced noise levels.

Completed annual heating maintenance on Bryant system. Performed comprehensive inspection of furnace components including gas valve assembly, burner assembly, heat exchanger, and blower motor. Verified proper operation of all safety controls and electrical connections. Inspected and tested programmable thermostat functionality, confirming accurate temperature reading and proper communication with heating system. Checked venting system including PVC intake and exhaust pipes for proper installation and secure mounting. All components found operating within manufacturer specifications with no issues identified.

Responded to no heat call on 8+ year old TM9E060B12MP11A direct vent furnace located in basement. Upon inspection, identified significant rust and corrosion on horizontal drain pipe above condensate coil, consistent with reported water leakage issue. Performed diagnostic evaluation of blower motor and all electrical components; all motors tested within normal operating parameters and no motor replacement was required at this time. Advised that corroded drain line requires replacement to prevent further water damage to coil assembly and surrounding components.

Completed comprehensive tune-up on 21-year-old BRYA model 355MAV042080 gas furnace located in basement. Performed standard maintenance protocol including inspection of heat exchanger, burner assembly, ignition system, gas valve operation, and all electrical connections. Verified proper operation of blower motor, flame sensor, pressure switches, and safety controls. Cleaned burners, checked and adjusted gas pressure, tested thermostat communication, and confirmed adequate airflow throughout system. Inspected flue pipe and venting for proper draft and clearances. All components found to be functioning within manufacturer specifications with no immediate repairs required. Unit operating properly at time of service completion.

Conducted on-site assessment for natural gas furnace replacement in basement location. Evaluated existing 30+ year old operational unit and documented current ductwork dimensions and configuration to determine proper equipment sizing and installation requirements for replacement system.

Completed full installation of Mitsubishi Electric mini-split heat pump system including outdoor condenser unit mounted on exterior wall with proper brackets, refrigerant line sets routed vertically with white line covers, electrical junction box installation, and new dedicated circuit. All mechanical and electrical permits obtained and work performed to code specifications, with system tested and operational upon completion.

Provided comprehensive estimate for complete HVAC system replacement in basement location, including furnace and air conditioning unit. Current 20-year-old equipment is operational but has reached end of expected service life. Assessed existing installation configuration, ductwork connections, electrical service, condensate drainage system with PVC piping, and available space in mechanical room for new equipment installation.

Responded to callback for hot water heater leak following previous day's HVAC installation. Inspected 110K BTU furnace and 3.5 ton A/C system with coil installation. Upon arrival, identified significant rust corrosion and water leakage at base of water heater unit, with moisture damage visible on concrete floor and ventilation grill showing extensive rust staining. Documented equipment condition with photos showing compromised water heater integrity and newly installed HVAC system components including flexible ductwork connections. Determined water heater failure unrelated to recent furnace and air conditioning installation work.

Completed full HVAC system installation including 110,000 BTU furnace and 3.5 ton air conditioning unit with evaporator coil. Installed furnace in basement utility area with proper ductwork connections, PVC condensate drainage system, and electrical conduit routing. Positioned outdoor condensing unit on concrete pad with refrigerant line set connection to exterior wall, completed electrical hookup through junction box, and verified all system components operational. All equipment properly secured, permits obtained, and installation meets mechanical code requirements.

Completed installation of 50-gallon tanked water heater (model RG250T6N) in basement utility area. Connected unit to existing copper supply lines, installed proper pressure relief valve, and verified all plumbing connections for code compliance. Permit was obtained prior to installation, and all work was performed according to manufacturer specifications and local plumbing regulations.

Conducted on-site assessment of existing 4-year-old air conditioning system and evaluated facility requirements for data center cooling application. Inspected current HVAC equipment and structural spaces including basement area with wood paneling and unfinished storage areas to determine feasibility for installing 6-7.5 ton cooling capacity. Documented existing conditions through photographs and provided replacement estimate for upgraded system to accommodate immediate data center cooling needs.

Completed annual heating maintenance inspection on residential HVAC system. Accessed unit interior and performed comprehensive visual inspection of all components. Examined electrical connections, wiring bundles, and control systems - all connections found secure with proper color coding intact. Inspected gas valve assembly and associated safety controls for proper operation. During inspection, identified significant corrosion and deterioration on copper refrigerant line, with heavy rust formation and surface degradation noted along horizontal run through unit compartment. Documented condition with photographs for maintenance records. Verified condensate drain line routing and condition. Assessed overall unit cleanliness, noting dust accumulation on interior surfaces consistent with normal operation. All mechanical components accessible during inspection appeared functional, though copper line corrosion will require monitoring or replacement to prevent future refrigerant leaks.

Completed comprehensive heating system maintenance as part of Air Care membership service. Performed full furnace tune-up including inspection of blower motor assembly, electrical connections, capacitor, control board, and all internal mechanical components. All wiring harnesses, relays, and electrical connections verified secure and functioning properly with no issues identified during inspection.

Responded to residential air conditioning service call for system evaluation and potential refrigerant concerns. Performed comprehensive assessment of outdoor condensing unit and indoor air handling components, documenting equipment condition through photographic documentation. Upon inspection, outdoor unit showed signs of age with weathered concrete pad and vegetation encroachment around base, while indoor ductwork and refrigerant lines displayed normal operational characteristics with proper mounting and connections intact.

Completed annual heating check on residential HVAC system. Performed comprehensive inspection of gas furnace components including heat exchanger, gas valve assembly, burner operation, electrical connections, and control boards. Replaced air filter and verified proper system operation and safety controls.