HVAC, Water Heater & Electrical Services in East Lansing, MI

Completed comprehensive fall furnace tune-up on three-year-old unit with no reported issues. Performed full system inspection including internal components, motors, electrical connections, and wiring verification. Inspected and documented air filter condition showing normal dust accumulation; filter examined for proper fit and airflow capacity. Verified draft inducer motor operation, checked all wire connections and terminal blocks for secure contact, and confirmed proper mounting of all mechanical components. All systems operating within normal parameters with no deficiencies noted.

Completed annual tune-up on one-year-old furnace and air conditioning system with both units operating properly. Performed comprehensive inspection of blower motor, capacitor, electrical connections, and wiring harnesses; verified all components functioning within manufacturer specifications. Provided homeowner education on proper air filter replacement procedures and recommended ongoing maintenance practices to ensure optimal system performance.

Completed annual heating maintenance on two HVAC systems. Performed comprehensive inspections of both units, including blower motor assemblies, electrical connections, and control modules. Replaced two humidifier pads and two furnace filters as scheduled. Verified proper electrical connections and wire management throughout mechanical compartments. Conducted temperature readings using calibrated instruments, recording supply air temperature of 45.1°F during system diagnostics. All components inspected and found to be operating within normal parameters. Systems tested and left in proper working condition for the heating season.

Completed annual maintenance on two air conditioning systems: a 30-year-old Amana unit and a 1-year-old Lennox unit, along with a 1-year-old forced air furnace. Performed comprehensive tune-up procedures including inspection of electrical connections, testing of compressor operation, verification of refrigerant lines, and examination of internal components and wiring on both AC systems. All equipment found to be operating within normal parameters with no issues identified during inspection.

Completed annual HVAC maintenance on residential heating and cooling system. Inspected and serviced furnace unit including blower motor, gas valve assembly, electrical connections, and wiring; verified thermostat operation and calibration. All components found to be in functional condition with routine maintenance performed per manufacturer specifications.

Conducted site assessment for electric vehicle charging station installation at residential property. Evaluated existing electrical infrastructure, including main breaker panel capacity and available circuits, to determine feasibility of EV charger installation. Inspected kitchen area where electric range is located to assess current electrical load and verified panel configuration with multiple existing circuits. Photographed electrical panel showing current wiring arrangement and available breaker spaces for potential dedicated EV charging circuit. Confirmed homeowner currently owns electric vehicle requiring charging capability. Provided comprehensive estimate for installation of Level 2 EV charging station, including required electrical upgrades, dedicated circuit installation, and proper grounding requirements to meet current electrical codes.

Completed annual HVAC maintenance inspection on residential furnace system. Performed comprehensive inspection of all internal components including blower motor assembly, electrical connections, wiring harnesses, control board, heat exchanger, and ductwork connections. Verified proper operation of all mechanical and electrical systems, checked duct connections and seals, and documented equipment condition through photographic documentation for maintenance records.

Completed scheduled Air Handler Maintenance (AHM) on residential HVAC system. Performed comprehensive inspection of furnace/air handler unit, ductwork connections, and condensate drain lines. Verified thermostat operation on both digital and analog units, confirmed proper temperature readings and system communication. All components found operating within normal parameters with no deficiencies noted.

Conducted comprehensive assessment of non-operational 14-year-old RUUD Weather King outdoor condensing unit for complete system replacement estimate. Evaluated existing exterior unit placement, electrical service connections including meter configuration and grounding, condensate drainage routing via PVC piping, and associated indoor mechanical components including basement ductwork, refrigerant line sets, and HVAC infrastructure. Documented current system configuration through photographic records to provide accurate replacement specifications and equipment sizing recommendations for aged air conditioning system.

Completed annual HVAC maintenance service including inspection of furnace gas valve assembly, burner system, and flame sensors. Replaced air filter and performed system safety checks, confirming proper operation of all mechanical and electrical components.

Completed routine cooling maintenance and AC tune-up as part of Air Care membership with no issues reported. Performed comprehensive system inspection of outdoor air conditioning unit, verified proper operation of all components, and checked refrigerant levels. Inspected indoor air filter showing good condition with clean pleated media in place, and confirmed Lennox digital thermostat displaying proper temperature readings at 73°F with humidity level at 65%, though noted Wi-Fi connectivity issue on display.

Completed annual preventative maintenance on Bryant residential HVAC system including both heating and cooling components. Performed comprehensive inspection of furnace unit, verified heat exchanger integrity and burner operation, checked blower motor function and electrical connections, inspected PVC venting system for proper drainage and exhaust flow, and replaced air filters. Tested system operation under heating mode with visible ignition sequence, confirmed all safety controls functioning properly, and verified proper airflow throughout the system. Unit operating within manufacturer specifications with no issues identified.

Completed annual fall furnace maintenance tune-up on residential heating system. Replaced air filter, installed new humidifier pad, and activated humidifier for the heating season. Performed comprehensive system inspection, verified all components operating properly with no safety concerns or deficiencies noted.

Completed on-site evaluation of 18+ year old natural gas furnace located in basement mechanical room. Unit currently operational but assessed for replacement estimate due to age and efficiency considerations. Documented existing equipment configuration including gas supply lines, venting system, ductwork connections, and surrounding plumbing infrastructure to determine replacement specifications and installation requirements.

Conducted on-site estimate for new hanging heater installation in pole barn structure with metal corrugated siding and finished interior workspace. Assessed installation requirements for space currently housing recreational vehicles and equipment, including proper clearances, venting needs, and optimal mounting location on metal wall assembly. Documented site conditions and building specifications through photographs to determine appropriate unit sizing and installation approach for this new construction heating application.

Completed annual heating maintenance on two units. Performed comprehensive inspection of furnace components, including heat exchanger examination, burner assembly assessment, and ignition system verification. Checked and tested all safety controls, limit switches, and flame sensors for proper operation. Inspected blower motor, cleaned blower assembly, and verified proper airflow. Examined gas connections, tested for leaks, and confirmed proper combustion. Measured temperature rise across heat exchanger to ensure equipment operating within manufacturer specifications. All systems tested and confirmed operational for the heating season.

Installed Bradford White tanked water heater in basement utility area with proper copper pipe connections and venting. Completed mechanical permit work including reconnection of all supply and discharge lines to manufacturer specifications. Unit positioned between existing furnace and utility wall with all safety labels visible and accessible for future reference.

Returned to site to complete sold repair on outdoor HVAC unit. Successfully replaced defective PCB control board (part #2523383) and failed fan motor (part #6024031). System tested and verified operational upon completion, with all components functioning within manufacturer specifications.

Completed mechanical installation of 2.5 ton air conditioning system with coil in left side yard location. Installed new outdoor condenser unit on concrete pad, established proper drainage with PVC piping system, and mounted electrical disconnect box with reconnection of power supply. Replaced communicating thermostat and integrated RDS into the system to address possible recall issue, ensuring proper communication between components and optimal system operation.

Completed AHM spot check on HVAC system. Inspected thermal limit switch assembly and removed component for examination, revealing three-disc thermal fuse configuration with star-pattern cutouts. Evaluated condensate drain connections and PVC piping, noting accumulated debris and dust on drain line and rubber coupling secured with hose clamp. Assessed system components and documented conditions with photos for maintenance records.