HVAC, Water Heater & Electrical Services in East Lansing, MI

Responded to service call for water intrusion through water heater vent during heavy rainfall. Upon inspection, identified improper vent termination allowing rainwater to enter the flue system and drip from the atmospheric vent hood. Examined the galvanized vent pipe configuration and confirmed lack of adequate weather protection at the exterior termination point. Recommended installation of a proper vent cap or rain collar to prevent future water infiltration while maintaining proper draft and combustion air requirements for the natural draft gas water heater.

Conducted on-site evaluation for new tankless water heater installation in residential property. Assessed existing plumbing infrastructure, including copper supply lines and shut-off valves in utility area, and documented current water heater configuration. Provided comprehensive estimate for tankless unit installation, including necessary modifications to gas lines, venting requirements, and electrical connections to support on-demand water heating system.

Responded to commercial HVAC replacement estimate for non-heating furnace system located in utility room. Assessed existing Carrier furnace and air handler configuration with associated electrical panel, refrigerant lines, condensate drainage, and ductwork connections. Documented current equipment condition, internal blower motor assembly, control components, and existing installation setup including PVC piping, copper lines, and electrical connections to provide comprehensive replacement quote for failed heating system.

Responded to no heat call at residential property. Upon inspection of furnace located in utility room, discovered electrical wiring issues within the blower compartment and significant debris accumulation on heat exchanger tubes. Inspected all electrical connections, terminal blocks, and capacitor assembly. Documented condition of internal components showing signs of age and operational wear. Cleaned debris from heat exchanger surfaces and verified proper wire routing and connections throughout electrical compartment. System evaluated for safety and operational concerns.

Completed comprehensive ComfortGuard maintenance visit on residential HVAC system including air handler unit and associated mechanical equipment. Performed standard inspection protocols on all accessible components, verified proper operation of condensate drain lines, checked electrical connections and refrigerant line integrity, and inspected ductwork and filtration system. All equipment found in operational condition with organized connections and clean surfaces maintained throughout the mechanical room installation.

Completed annual preventative maintenance on outdoor air conditioning condenser unit. Connected manifold gauge set to service ports and verified refrigerant pressures and system operating parameters within manufacturer specifications. Unit inspected, tested, and confirmed operational with no deficiencies noted.

Responded to complaint of exhaust fumes from water heater leaking into living space. Upon inspection, identified compromised venting system on tanked water heater allowing combustion gases to escape into the home rather than properly exhausting outside. Disassembled and replaced defective PVC vent piping components, including multiple elbow fittings that showed signs of deterioration and mineral deposits. Reinstalled proper venting configuration to ensure safe exhaust of combustion gases and verified all connections were secure and properly sealed to prevent future leakage into occupied areas.

Completed installation of new residential gas furnace in basement mechanical room. Installed vertical air handler unit with proper ductwork connections, integrated humidifier system with water supply lines, and white PVC condensate drain piping with appropriate support brackets. All equipment mounted securely on basement floor with professional routing of drainage lines, electrical connections, and sealed metallic duct joints at supply plenum.

Responded to no heat call for forced air furnace system of unknown age. Upon inspection, assessed existing furnace and HVAC equipment configuration in basement mechanical room. Evaluated system condition and determined replacement was more cost-effective option than repair. Provided comprehensive estimate for complete furnace replacement, documenting existing equipment specifications, ductwork connections, and installation requirements. Photographed current system setup including furnace cabinet, humidifier unit, ductwork configuration, and internal components to support replacement quote and ensure proper equipment sizing for new installation.

# HVAC Maintenance - ACM Service Report Completed routine Air Conditioning Maintenance (ACM) on Lennox outdoor condensing unit. Performed comprehensive system inspection including visual assessment of electrical components, capacitor, contactor, and wiring connections. All electrical connections verified secure with proper wire routing observed. Capacitor examined and found in good operating condition with no signs of bulging or deterioration. Contactor terminals inspected and confirmed clean with no pitting or damage. Refrigerant lines and condensate drain checked for proper installation and functionality. Unit exterior panels and housing inspected with no structural concerns noted. System operational with no deficiencies identified during maintenance visit.

# Service Report Responded to no heat call on 1-year-old furnace located in basement. Upon arrival, conducted diagnostic inspection of unit with access panels removed to identify cause of heating failure. Inspected all internal components including blower motor assembly, gas valve, pressure switches, condensate drain system, and electrical connections throughout upper and lower compartments. Verified proper operation of all mechanical and electrical systems. Checked venting system including PVC exhaust and intake pipes for proper installation and clearances. Examined wiring connections and found some disorganization but all connections secure and functional. Restored heat to unit and confirmed normal operation. Completed Annual HVAC Maintenance inspection as time permitted, including full system evaluation and performance verification. Documented equipment condition with photos showing internal components and overall unit configuration. Unit operating properly at time of departure. Pa

# HVAC Install - Complete System ## Summary Successfully completed full HVAC system replacement including installation of 110,000 BTU furnace and 4-ton air conditioning unit with left-side configuration, humidifier integration, and reconnection of all existing utilities. ## Work Performed Removed existing HVAC equipment and installed new Lennox furnace system with 110,000 BTU heating capacity in basement mechanical room. Mounted furnace cabinet on concrete floor with proper clearances and secured unit to manufacturer specifications. Installed 4-ton air conditioning system with left-side refrigerant line configuration to match existing infrastructure. Connected air handler plenum to furnace discharge and secured all ductwork connections with appropriate sealing methods. Installed silver-insulated rectangular plenum above furnace unit and connected black flexible ductwork for proper air distribution. Integrated humidifier system into new furnace installation, connecting water supply

Completed installation of a complete HVAC system, including a 110,000 BTU furnace, 5-ton AC unit, and humidifier in residential location. System features Lennox equipment with proper PVC venting, new ductwork connections, and all components were successfully installed according to manufacturer specifications and local mechanical permit requirements.

Performed comprehensive evaluation of 32-year-old furnace and A/C system located in utility room. Unit is currently operational but at end of expected service life. Inspected exposed internal components including control board, wiring harness, and ductwork connections. Provided replacement options for complete system upgrade to improve efficiency and reliability.

Performed scheduled ComfortShield maintenance on 4-year-old Lennox system (warranty through 05-2026). Inspected and replaced air filter on furnace unit. System is functioning properly with no operational issues detected. Confirmed water heater (Rheem Performance) is in good working condition. All components are operating within manufacturer specifications.

Performed annual maintenance on recently installed furnace system. Inspected all internal components including wiring, controls, and mechanical parts. Verified proper operation of drainage/ventilation system with particular attention to PVC connections and elbow joints. Unit is operating within manufacturer specifications with no issues identified.

Performed diagnostic assessment on 13-year-old non-operational furnace located in basement. System exhibited zero activity when calling for heat. Visual inspection of the unit revealed potential issues with the ignition system and possible control board malfunction that will require replacement of components to restore heating functionality.

Performed routine maintenance on forced air furnace reporting no heat. Inspected and cleaned flame sensor with abrasive pad to remove corrosion buildup that was causing system failure. System now functioning properly with restored heating operation.

Performed tune-up service on Bryant gas furnace. Discovered significant rust and corrosion around the heat exchanger and drainage components. Cleaned clogged condensate line to restore proper drainage and addressed startup noise by lubricating moving parts and securing loose components.

Conducted a comprehensive assessment of a non-operational mini split system in the kitchen area. Visual inspection revealed a wall-mounted unit installed above stainless steel cabinets requiring service. System was previously installed in 2023 and is now being evaluated for potential air conditioning repairs or replacement.