HVAC Repair & Electrical Services in Okemos, MI

Completed installation of 2.5-ton air conditioning system with evaporator coil on left side of residence. Unit positioned on gravel pad with proper drainage, electrical disconnect and components mounted to exterior wall with conduit connections. All permits obtained, system reconnected and operational upon completion.

Performed on-site assessment of 16-year-old residential air conditioning system with reported failed outdoor unit. Inspected existing Goodman furnace, Space-Gard high efficiency air cleaner, ductwork configuration, and refrigerant line routing in basement utility area. Documented current system layout including galvanized metal plenum, flexible insulated ductwork, copper refrigerant lines, and floor-mounted air handler to provide comprehensive replacement estimate for complete AC system.

Responded to service call for 3-year-old A/C system struggling to maintain temperature, with unit set to 70°F but indoor temperature reaching 80°F. Upon arrival, found evaporator coil and refrigerant lines severely frozen with substantial ice buildup throughout the system. Documented frozen coil condition with photos showing complete frost coverage on copper tubing, expansion device, and surrounding components. Instructed system shutdown to allow complete ice melt before diagnostics could proceed, as frozen conditions prevent accurate assessment of underlying issues such as potential low refrigerant charge, restricted airflow, or failed blower motor.

Responded to no cooling call on residential central air conditioning system. Upon arrival, found Lennox thermostat displaying but system not responding to cooling demand. Verified thermostat was calling for cooling with setpoint at 75°F and indoor temperature reading 73°F. Inspected outdoor Lennox condenser unit and found no power to compressor or condenser fan motor. Checked electrical disconnect at exterior wall and discovered tripped breaker. Reset breaker and restored power to condensing unit. System started successfully with compressor and condenser fan operating normally. Verified proper airflow through condenser coils and confirmed adequate clearance around unit despite surrounding landscaping. Monitored system operation through complete cooling cycle. Thermostat responded appropriately to temperature changes and system cycled off at setpoint. Advised homeowner to monitor for any repeat occurrences that may indicate underlying electrical issue requiring further diagnosis.

Completed comprehensive spring maintenance and tune-up on residential central air conditioning system. Performed thorough inspection of indoor air handler unit and outdoor condenser unit, checking all electrical connections, refrigerant levels, and system controls. Cleaned condenser coils, verified proper airflow through both units, tested system operation and confirmed all components functioning within normal parameters with no issues identified.

Conducted comprehensive assessment of existing 21-year-old furnace and air conditioning split system for replacement estimate. Documented equipment dimensions and specifications through detailed measurements and photography of evaporator coil assembly and exterior condensing unit clearances. Provided homeowners with equipment replacement options and recommendations for upgrading aging HVAC system, with installation planned for upcoming weeks.

Completed annual maintenance service on Carrier furnace model 69TPGBU60V171214 (60,000 BTU input) and air conditioning unit model CNPVP3017ALA01AA utilizing R-410A refrigerant. Performed comprehensive inspection of both heating and cooling systems, verified manufacturer specifications, documented serial numbers and equipment condition through photographic records. All components operating within normal parameters, no deficiencies noted requiring immediate attention.

Completed full HVAC system replacement in basement utility area, including furnace and air conditioning unit after existing equipment failed and was deemed non-functional by previous assessment. Installed new heating and cooling equipment with proper integration to existing ductwork system, ensuring all connections to insulated supply ducts and mechanical components were properly secured and operational.

Completed annual cooling maintenance on HVAC system. Inspected evaporator coil and found heavy accumulation of dust and debris throughout the fin assembly, significantly restricting airflow. Documented condition of copper refrigerant lines showing normal oxidation patina, verified all tube connections and brazed joints for integrity, and photographed internal components including coil assembly and associated piping for maintenance records.

Completed annual Air Care Cooling maintenance on residential HVAC system. Performed comprehensive inspection of air handler unit, ductwork, electrical components, and blower motor assembly in attic installation. Verified all electrical connections and control systems operating properly. Confirmed system does not require filter replacement at this time as existing filter remains in acceptable condition.

Completed annual cooling maintenance on residential outdoor condenser unit. Performed comprehensive system inspection, verified unit operation, checked refrigerant lines and electrical connections, and cleaned condenser coils. Unit found in good working condition with no issues identified.

Completed full installation of 3-ton Lennox air conditioning condenser unit and evaporator coil system in residential property. Outdoor condenser positioned on pad in backyard with proper clearance for airflow, connected to indoor evaporator coil mounted on existing furnace in basement utility area. Installed refrigerant line set connecting outdoor and indoor components, completed all electrical connections for right-side configuration, and reconnected system per mechanical permit specifications. System tested and verified operational upon completion.

Performed comprehensive air conditioning tune-up on outdoor condensing unit, including electrical diagnostics with digital multimeter to verify system voltage and amperage readings. All measurements were within manufacturer specifications, condenser coils inspected, and unit confirmed operational for the cooling season.

Completed comprehensive 5-year ComfortGuard maintenance inspection on heating and cooling system. Performed thorough cleaning of internal components including blower assembly, control board area, and housing using specialized cleaning tools and microfiber materials. Inspected all electrical connections, wiring harnesses, and safety controls for proper operation and secure mounting.

Completed annual cooling maintenance on residential air conditioning system. Connected manifold gauges to outdoor condenser unit and verified refrigerant pressures within manufacturer specifications. Inspected condenser coil condition, fan motor operation, and electrical connections at disconnect box. Unit operating properly with no deficiencies noted at time of service.

Completed comprehensive air conditioning tune-up on residential system. Performed inspection of indoor blower motor assembly, verified proper operation and documented equipment serial numbers. Conducted outdoor condenser unit evaluation, checked refrigerant pressures using manifold gauges, and confirmed system operating within manufacturer specifications.

Completed annual cooling maintenance on Bryant HVAC system. Performed comprehensive inspection of furnace unit, air handler, and associated ductwork including metallic vent piping and connection points. Inspected and serviced air filter, verifying proper airflow and system operation with no issues identified during the maintenance visit.

Completed electrical estimate for replacement of existing whole home generator system. Evaluated current Kohler generator unit installed on concrete paver pad in backyard with proper clearances and ventilation. Assessed electrical infrastructure including Kohler transfer switch and associated wiring in basement utility area to ensure compatibility with replacement unit specifications.

Completed annual cooling maintenance on HVAC system. Performed electrical diagnostics using multimeter, verified voltage readings at outdoor condenser unit registering 503V, inspected compressor and heat exchanger components, checked electrical connections and junction boxes in mechanical room, and documented equipment condition with photos. All components operating within normal parameters upon completion of maintenance inspection.

Conducted on-site assessment for whole-house generator installation at single-family residential property. Evaluated electrical service panel location, existing utility infrastructure, and optimal generator placement near basement utility area with accessible floor drain for condensate management. Documented interior electrical load requirements including major appliances and provided recommendations for appropriate generator sizing and automatic transfer switch installation to meet homeowner's backup power needs.