HVAC, Water Heater & Electrical Services in East Lansing, MI

Responded to no-cool condition on 15-year-old Carrier central air conditioning system. Upon arrival, confirmed indoor blower motor operational but outdoor compressor unit not engaging. Inspection revealed failed dual run capacitor with severe corrosion and rust on terminal connections, preventing compressor and condenser fan motor from starting. Replaced defective capacitor, verified proper voltage and amperage readings, and restored system to normal cooling operation. System tested and confirmed operational before departure.

Performed maintenance on 15-year-old Bryant furnace and outdoor condenser unit. Addressed customer concern of no cooling, only fan operation. Removed stuck air filter and installed replacement filter. Inspected condensation pump which was found dry upon arrival. Completed full system maintenance including condenser coil cleaning and operational testing of both heating and cooling components.

Completed full system estimate for residential HVAC replacement. Assessed existing undersized 3-ton Lennox system with refrigerant leak requiring annual recharge. Documented current equipment installation in utility closet, measured available clearances, and photographed furnace configuration, ductwork connections, and spatial constraints to determine feasibility of upgrading to properly-sized 4-5 ton system.

Completed scheduled air conditioning maintenance on Bryant HVAC system. Performed comprehensive inspection of air handler unit, verified proper operation of all components, and inspected ductwork showing condensation accumulation on galvanized supply plenum. Replaced air filters with new pleated media filters to maintain proper airflow and system efficiency.

Completed estimate for replacement of existing Mitsubishi mini split system serving 10x10 office area. Assessed current outdoor condensing unit mounted on exterior brick wall and indoor air handler with refrigerant line set. Documented existing installation including electrical disconnect, conduit routing, and line set penetration through building envelope. Photographed equipment condition and installation configuration to prepare comprehensive replacement proposal for commercial mini split system.

Provided comprehensive estimate for replacement of 22-year-old air conditioning system currently located in basement. Performed detailed measurements and assessment of existing equipment and installation space to determine proper sizing and configuration requirements for new system replacement.

Completed annual cooling maintenance on residential HVAC system. Inspected air filter showing moderate dust accumulation along bottom edge, checked furnace unit and associated ductwork components for proper operation, and verified all mechanical systems in basement installation were functioning within normal parameters.

Conducted comprehensive site assessment for electrical panel upgrade in residential utility area. Documented existing electrical infrastructure including main panel, junction boxes with GFCI protection, and conduit routing. Photographed current panel configuration, associated electrical components, and surrounding plumbing systems to ensure proper clearance requirements for upgrade work. Verified accessibility to panel location and water meter for accurate estimate preparation.

Completed comprehensive preventive maintenance on a two-year-old central air conditioning system operating within normal parameters. Performed full system inspection including evaporator coil assembly with reflective insulation, verified proper refrigerant line connections and securing, and inspected condensate drain system with PVC piping and shut-off valve for proper operation. Replaced air filter showing moderate dust accumulation to maintain optimal airflow and system efficiency. All components functioning as designed with no deficiencies noted.

Responded to service callback for tripping breaker affecting 6-year-old A/C unit located in basement. Inspected main electrical panel and circuit breaker configuration, verified proper breaker sizing and connections for A/C circuit, and documented panel condition with circuit directory labeling. Resolved breaker tripping issue to restore cooling system operation.

Completed full HVAC system installation including a 70,000 BTU gas furnace with evaporator coil, 2.5-ton air conditioning condenser unit positioned at rear of property, and RG240S6N residential water heater. Installation included humidifier integration, refrigerant line connections, condensate drainage, electrical wiring, and gas line reconnection for both furnace and water heater. Installed and programmed Sensi digital thermostat with multi-stage heating and cooling controls. All equipment tested and verified operational, with proper airflow, temperature differentials, and safety controls confirmed. System commissioned and left in full working order with all permits requested for mechanical work.

Responded to no-cooling complaint with outdoor condensing unit failing to start. Upon arrival, performed diagnostic evaluation of central air conditioning system. Inspected outdoor unit positioned on exterior wall, checked electrical connections at disconnect box, and verified power supply. Tested capacitor, contactor, and compressor functionality. Identified failed component preventing unit operation, completed necessary repairs to restore system functionality, and verified proper operation of condensing unit with successful startup and normal cooling cycle.

Conducted on-site evaluation for complete mini split system installation in owner-occupied residence with no existing HVAC system. Assessed interior mounting locations and exterior placement requirements for condenser unit. Documented proposed indoor head unit location on interior wall and evaluated exterior side yard area with concrete pad access for outdoor condenser placement. Reviewed electrical requirements, refrigerant line routing through exterior wall, and condensate drain provisions for whole-home coverage.

Conducted full system estimate for residential HVAC replacement on 1997 original equipment with non-functioning air conditioning unit and 16-year-old heating system. Performed comprehensive evaluation of existing ductwork infrastructure, documenting measurements and assessing condition of metal ducting and flexible connections for compatibility with new equipment installation. Provided homeowner with replacement options for complete heating and cooling system to address immediate cooling failure and aging furnace requiring urgent replacement.

Completed comprehensive ComfortGuard maintenance package including full system inspection and component evaluation. Inspected humidifier assembly and evaporator pad, noting significant mineral buildup and calcium deposits throughout the honeycomb mesh structure, which is typical with hard water exposure over extended use. Examined return air ventilation grille and louvers, confirming proper airflow and clean operational condition with no obstructions or maintenance issues identified.

Completed comprehensive 5-year ComfortGuard maintenance visit on Lennox residential HVAC system. Performed thorough inspection of furnace interior components including blower motor assembly, electrical connections, control boards, and wiring harnesses. Examined humidifier evaporator pad, noting mineral deposit accumulation and moisture saturation levels in lower section; verified water supply line connections and proper operation. Inspected all safety controls, ductwork connections, and PVC condensate drainage system. Confirmed proper function of all mechanical and electrical components throughout the heating system.

Completed full HVAC system installation including a 110,000 BTU furnace and 4-ton air conditioning unit configured for right-side orientation. Performed mechanical installation with all necessary reconnections to existing infrastructure, installed condensate pump with PVC drainage piping, and ensured proper electrical connections throughout the system. All equipment tested and verified operational upon completion.

Conducted on-site evaluation for furnace replacement estimate. Assessed existing 20-year-old furnace system located in basement mechanical room alongside water heater. Documented current equipment configuration including ductwork layout, venting arrangements, and spatial considerations for replacement unit installation. Customer requesting replacement within three-month timeframe due to age of existing equipment.

Conducted comprehensive assessment of existing 40-year-old air conditioning system for replacement quote. Evaluated whole-home HVAC infrastructure including outdoor condensing unit, indoor air handler, and distribution ductwork. Documented supply register dimensions and photographed existing duct configuration, copper refrigerant lines, and mechanical connections to provide accurate replacement specifications and ensure proper system sizing for new equipment installation.

Conducted site evaluation for air conditioning system replacement estimate at residential property with basement-located HVAC equipment. Current AC unit is non-operational due to concerns about mold and mildew contamination following recent moisture remediation work, including newly installed basement pump system. Assessed existing furnace installation, ductwork configuration, and mechanical room conditions to determine appropriate replacement equipment specifications and integration requirements with current heating system infrastructure.