HVAC, Water Heater & Electrical Services in East Lansing, MI

Completed annual ComfortGuard maintenance on both the furnace and air conditioning system for a whole-home HVAC setup. Both units, originally installed by Hager Fox approximately five years ago, were thoroughly inspected and serviced. Performed comprehensive AC tune-up including inspection of refrigerant levels, electrical connections, and condenser components. Examined furnace interior components including gas valve assembly, control board, ignition system, and all electrical wiring connections. Verified proper operation of the circuit board and safety controls. Inspected and documented air filter condition. All systems tested and confirmed to be operating within manufacturer specifications with no deficiencies noted. Both heating and cooling systems remain in excellent working condition.

Completed 5-year recurring ComfortGuard maintenance visit on air handling unit. Inspected interior components and observed rust-colored staining on metal drain pan indicating previous water accumulation or corrosion. Replaced humidifier pad and air filter as preventative maintenance measures to ensure optimal system performance and air quality.

Responded to service call for water leakage from furnace occurring when air conditioning system was in operation. Upon arrival, inspected 11-year-old HVAC system located in basement. Found evidence of significant water damage and rust staining on top surface of furnace cabinet, indicating ongoing condensate drainage issue. Removed access panel and performed thorough internal inspection of furnace components, blower assembly, and condensate management system. Identified condensate drain line obstruction causing water backup and overflow onto furnace cabinet during AC operation. Cleared blockage from drain line and verified proper drainage flow. Inspected evaporator coil, drain pan, and associated plumbing connections for additional issues. Tested system operation in cooling mode to confirm water is now draining properly through condensate lines without leakage. System operating as designed with no further water discharge onto equipment.

Performed air conditioning startup and inspection on Lennox condensing unit (Model SX35365-6F-20). Unit was successfully energized and operational following winter shutdown. Exterior cabinet showed significant dust and debris accumulation but unit functioned properly upon startup. Verified refrigerant specifications and safety labels present on equipment.

Responded to callback for air conditioning system not responding to thermostat commands and remaining stuck at 75 degrees. Inspected HVAC system components including refrigerant lines with pipe insulation, replaced air filter and evaporator pad, and verified proper thermostat communication with air handler to restore normal temperature control functionality.

Successfully installed a 17-gallon whole-home humidifier unit in the basement mechanical room, integrating it with the existing HVAC system. Connected the humidifier to the main furnace ductwork using appropriate flex duct routing, and established water supply lines using white PVC plumbing to ensure proper humidity delivery throughout the home. Completed all electrical connections, verified operational functionality, and ensured proper drainage configuration to the existing floor drain system.

Responded to service call for non-functional condensate pump on a 4-year-old central air conditioning system. Upon inspection, confirmed condensate pump failure preventing proper drainage from the HVAC unit. Replaced faulty condensate pump assembly, tested operation to verify proper condensate removal, and confirmed system returned to normal cooling function with adequate drainage.

Completed annual cooling maintenance on residential Luxaire HVAC system. Inspected furnace unit, air handler, and associated ductwork for proper operation and component condition. Accessed filter compartment and documented mesh filter condition showing significant dust and debris accumulation throughout the filter media. Photographed system configuration including condensate drain lines, flexible vent connections, and electrical wiring for service records. All major components visually inspected and system operational status verified.

Completed annual HVAC maintenance on air handler unit, including inspection of blower assembly and cabinet condition noting rust staining on upper housing. Replaced dirty pleated air filter with accumulated debris to restore proper airflow and system efficiency.

Completed comprehensive 5-year recurring ComfortGuard maintenance inspection on residential HVAC furnace system. Performed full system evaluation with access panel removed to inspect internal components including blower motor assembly, gas valve operation, refrigerant line connections with protective caps, electrical wiring harness, and mounting hardware. Replaced standard air filter with clean pleated media filter rated for proper airflow and filtration efficiency. All mechanical and electrical components found in proper working condition with no deficiencies noted during inspection.

Completed annual HVAC maintenance inspection on residential furnace system. Performed comprehensive system check including inspection of gas valve assembly, blower motor, electrical connections, control boards, and all internal components. Replaced air filter and humidifier pad as part of routine maintenance protocol to ensure optimal system performance and efficiency.

Responded to no-cooling complaint on 10-year-old central air conditioning system. Upon arrival, confirmed outdoor condenser unit was running with fan operation but no refrigerant circulation evident—suction line at outdoor unit remained ambient temperature indicating compressor failure or complete refrigerant loss. Connected manifold gauges to service ports for diagnostic pressure readings. Based on system age, ambient line temperatures, and lack of cooling capacity, recommended evaluation for compressor replacement versus full system replacement due to age and efficiency considerations.

Completed comprehensive AC tune-up on 1-year-old residential air conditioning system. Performed standard maintenance protocol including condenser coil cleaning, refrigerant level verification, electrical connection inspection, and thermostat calibration. Verified correct air filter specification and installation per manufacturer requirements, confirmed outdoor unit operating within normal parameters on concrete pad with proper clearances maintained.

Completed comprehensive assessment of existing HVAC system and ductwork configuration in attic space for full system replacement estimate. Inspected accessible areas including flexible duct routing, structural clearances, and installation pathways to determine equipment specifications and labor requirements for new system installation.

Completed estimate for replacement of non-functional air conditioning system and furnace in ranch-style home with basement installation. Assessed existing natural gas forced air system rated 15+ SEER, evaluated electrical panel capacity and circuit requirements, and documented current equipment configuration to provide comprehensive replacement options for both heating and cooling units.

Completed annual cooling maintenance on residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, including examination of coil condition, fan operation, and electrical components. Unit found in operational condition with proper clearance from surrounding vegetation. Documented equipment condition with photos for service records.

Completed installation of 3-ton air conditioning system with evaporator coil in basement utility area. Connected refrigerant lines to existing furnace, installed copper piping with proper insulation, and integrated all ductwork connections. Verified all electrical connections, tested system operation, and ensured proper airflow through newly installed components.

Completed comprehensive 5-year ComfortGuard maintenance service on Lennox outdoor condensing unit and indoor air handling system. Performed thorough inspection of outdoor unit, noting minor weathering and organic growth on top surfaces with debris accumulation between protective grilles. Cleaned condenser coils and removed webbing from side grille openings. Replaced evaporator cooling pads as requested specialty service. Inspected and serviced return air filter housing, addressing accumulated dust and debris on filter media. Verified proper airflow through ventilation grilles and confirmed system operational parameters within manufacturer specifications.

Responded to customer complaint of low airflow and warm air from basement-located air conditioning unit installed in 2019. Upon inspection, diagnosed failed dual-run capacitor (45/5 μF, 440VAC) preventing proper compressor and condenser fan motor operation. Replaced defective capacitor with new unit, restored system to normal operation, and verified adequate airflow and cooling performance.

Completed routine air conditioning maintenance on residential HVAC system. Performed comprehensive inspection of condensing unit, verified proper refrigerant pressures and system operation, confirmed thermostat functionality displaying 78°F indoor temperature with cooling mode engaged and set point at 68°F, and documented equipment condition through photographic records.