HVAC, Water Heater & Electrical Services in Grand Ledge, MI

Completed full HVAC system installation including a 70,000 BTU furnace, 3-ton air conditioning unit with matching evaporator coil, and humidifier. The outdoor condensing unit was positioned on a concrete pad in the right side yard with proper electrical disconnect and conduit installation. Inside the mechanical room, installed the new furnace on the concrete floor with all required PVC venting routed through existing ductwork pathways, connected supply and return ductwork using proper transitions and flexible connectors, and integrated the humidifier into the system. Reconnected all electrical components, tested system operation to verify proper heating and cooling functionality, and ensured all connections met code requirements per mechanical permit specifications.

Completed routine maintenance tune-up on 8-year-old forced air furnace and 3-year-old air conditioning system. Performed comprehensive inspection of furnace combustion chamber, burner assembly, blower motor, electrical connections, and safety controls. Inspected AC outdoor unit, verified refrigerant levels, checked electrical components, and tested system operation. All systems operating within normal parameters with no issues identified or repairs required.

Provided estimate for complete HVAC system conversion from non-functional boiler heating to forced air furnace and air conditioning system. Existing outdoor condenser unit shows significant age and weathering with overgrown vegetation, while interior office space currently utilizes baseboard heating requiring full ductwork installation and equipment replacement for modernized climate control.

Responded to third callback for furnace water leak and noisy blower motor on 2.5-year-old forced air system. Inspected condensate drain system and PVC drainage lines with purple-primed connections at air handler cabinet. Verified proper pitch and drainage flow through white PVC piping system, checked insulated refrigerant lines and copper tubing connections for condensation issues. Documented current installation configuration showing drain lines, insulated suction line with foam wrap, and equipment connections. System operational at time of inspection with heating function confirmed.

Conducted comprehensive evaluation of 22-year-old residential HVAC system for full replacement estimate. Assessed existing furnace installation in mechanical room, including extensive galvanized ductwork system, vertical cylindrical water heater integration, and copper piping configuration throughout basement utility space. Inspected exterior air conditioning condenser unit positioned on concrete pad, evaluating wire mesh protective housing, foundation ventilation components, and drainage systems. Documented all equipment specifications, ductwork layout, and mechanical connections through photographic records to provide accurate replacement system recommendations for aging equipment approaching end of service life.

Completed comprehensive AC tune-up and furnace maintenance on multiple Lennox systems as part of customer's 5-year maintenance plan. Performed routine inspection and servicing of 3-year-old Lennox WT 10-2027 units and 20-year-old Lennox system, verified proper operation of Lennox smart thermostat displaying 75°F indoor temperature with heating mode functionality, and confirmed all systems operating within normal parameters with no issues identified.

Completed annual maintenance tune-up on residential gas furnace system. Performed comprehensive inspection of all internal components including blower motor assembly, gas valve, electrical connections, and control boards. System was found to be in proper working order with all components operating within normal parameters; no repairs required at this time.

Completed comprehensive furnace cleaning and inspection tune-up on residential heating system. Accessed furnace cabinet, inspected blower motor assembly, electrical connections, control boards, and all internal components. Verified proper operation of all mechanical systems, checked wiring integrity across multiple colored wire connections, and confirmed all safety labels and manufacturer specifications were intact and visible.

Conducted estimate for furnace replacement on 20-year-old existing unit located in basement utility room. Assessed current system condition, noting aged equipment with moisture accumulation on ductwork and metal components. Evaluated installation space, existing ductwork configuration, wooden framing structure, and accessibility for replacement work. Documented equipment specifications, venting requirements, and electrical connections. Provided homeowner with comprehensive replacement options and recommendations based on current system layout and mechanical room conditions.

Responded to callback for furnace water leak and noisy blower motor on 2.5-year-old forced air unit. Upon inspection, discovered condensate drain line issue with PVC discharge pipe showing improper pitch. Verified condensate drain system, checked trap assembly, and confirmed proper drainage flow. Leveled and adjusted condensate line routing to ensure gravity drainage and prevent future water accumulation. Inspected blower assembly for noise concern - unit operating within normal parameters at time of visit. Documented installation with level measurements and photographed condensate piping configuration for records. System tested and confirmed heating operation with no active water leakage observed during service call.

Completed annual preventive maintenance tune-up on three HVAC systems: mini-split unit, furnace, and central air conditioning system, all Lennox equipment approximately 5 years old. Performed comprehensive inspection of all components, verified proper operation of thermostat controls, checked electrical connections and circuit boards, inspected condensate pump and drainage systems, and examined heat exchanger for any signs of deterioration. All systems found to be operating within normal parameters with no deficiencies noted.

Completed routine maintenance and tune-up on a 4-year-old residential air conditioning system with no reported performance issues. Performed comprehensive inspection of outdoor condenser unit, which showed normal weathering and dirt accumulation consistent with outdoor exposure. Cleaned condenser coils and exterior surfaces, checked refrigerant levels, verified electrical connections, inspected fan operation, and confirmed all components were functioning within manufacturer specifications for optimal system performance.

Responded to no cooling complaint on 10-year-old air conditioning system. Customer reported system blowing air but not cooling, with exterior refrigerant line showing ice buildup. Customer had already shut down cooling mode and ran fan-only operation for several hours prior to arrival. Performed system evaluation and provided estimate for full HVAC system replacement based on age of equipment, condition assessment, and repair versus replacement analysis.

Responded to no cooling complaint on 10-year-old air conditioning system. Upon arrival, confirmed unit was blowing air but not cooling, with visible ice buildup on outdoor refrigerant lines. Performed diagnostic testing using digital multimeter to assess system pressures and temperatures. Customer had already initiated proper recovery procedure by shutting down compressor and running fan mode to thaw frozen coil. Evaluated refrigerant line conditions and system performance parameters to determine root cause of icing condition, which typically indicates restricted airflow, low refrigerant charge, or compromised metering device requiring further service.

Responded to no cooling complaint on 30-year-old residential two-ton air conditioning system with inoperative outdoor condenser fan motor. Per customer request, replaced failed condenser fan motor and verified proper operation of condensing unit. System restored to cooling operation with all components functioning within normal parameters.

Completed scheduled maintenance on Goodman gas furnace model GM8S960803BNAA. Performed comprehensive inspection of internal components including gas valve assembly, burner chamber, pressure switches, and electrical connections. Replaced air filter and verified proper operation of all safety controls and system functionality.

Conducted site assessment of existing Generac whole house standby generator experiencing oil leak requiring replacement. Evaluated current installation location on exterior gravel pad adjacent to air conditioning unit, inspected transfer switch and electrical connections in basement utility room, documented equipment condition and configuration. Photographed generator unit, outdoor installation setup, interior electrical panel, and associated wiring to prepare comprehensive replacement estimate for new whole house generator system.

Returned to property to replace drain hose on mini split system serving bedrooms and completed ComfortGuard maintenance package including filter replacement. All work performed according to manufacturer specifications and system tested for proper operation upon completion.

Completed comprehensive ComfortGuard Maintenance Package including replacement of failed drain hose (part #71w36) and installation of new filters/pads. Performed full system inspection of HVAC equipment, verified refrigerant line connections and insulation integrity, and confirmed all mechanical components operating within manufacturer specifications.

Conducted site assessment for whole home generator installation. Evaluated existing electrical service entrance and meter location on exterior wall, noting overgrown vegetation requiring clearance for proper equipment access and ventilation compliance. Documented current utility infrastructure including water heater positioning in basement to determine optimal generator placement, fuel line routing, and transfer switch installation requirements. Assessment completed to provide comprehensive electrical estimate for Kohler/Generac generator system integration with existing residential electrical service.