HVAC, Electrical & Water Heaters in Mason, MI

Completed full HVAC system installation including a Lennox 70,000 BTU furnace and 2-ton air conditioning unit with right-side placement. Installed new Sensi programmable thermostat, ran new electrical circuit to support equipment, and connected all ductwork and refrigerant lines. All mechanical and electrical permits were obtained prior to installation, system was tested and confirmed operational upon completion.

Responded to recall for A/C system intermittently shutting off on 15+ year old unit located in basement. Performed diagnostic inspection of furnace and cooling system components, accessing internal compartment to examine blower motor, refrigerant lines, gas valve assembly, electrical connections, and safety controls including pressure switch. Verified proper operation of all mechanical and electrical components, checked wiring harnesses and connections for integrity, and inspected venting system. Unit found operating within normal parameters at time of inspection.

Conducted site assessment for new 2-zone mini split system installation in single-family residence requiring one outdoor condenser unit and two indoor wall-mounted air handlers for upstairs rooms measuring 96 and 110 square feet. Evaluated attic space for refrigerant line routing, electrical requirements, and condensate drainage pathways, documenting existing structural conditions including wooden framing, insulation placement, and available access points for installation. Assessed both interior room locations for optimal indoor unit placement, noting ongoing renovation work and confirming adequate wall space and electrical service availability for timely system deployment.

Performed annual cooling maintenance on HVAC system. Upon inspection, discovered evaporator coil completely frozen with heavy ice buildup across entire surface, indicating restricted airflow or low refrigerant charge. Identified cause as severely restricted airflow due to dirty/clogged filter media. Shut down system to allow coil to thaw completely. Replaced furnace filter as requested. Inspected condensate drain system and PVC drain lines for proper operation. Checked refrigerant lines, service valves, and brass fittings for leaks or damage. Once coil thawed, verified drain pan functionality and cleared any residual moisture. Reinstalled access panel and restored system to normal operation. Advised monitoring system performance to ensure ice buildup does not recur. System operating within normal parameters upon departure.

Provided comprehensive HVAC estimate for complete system replacement of 20+ year old non-operational natural gas forced air furnace and air conditioning system in colonial residence. Documented existing electrical panel configuration and utility room conditions, including water heater placement and plumbing infrastructure, to assess installation requirements and ensure proper system integration with home's existing electrical and mechanical systems.

Conducted comprehensive site evaluation for complete HVAC system replacement at owner-occupied residence. Assessed existing 25-year-old furnace for replacement and evaluated property for new central air conditioning installation where no AC system currently exists. Inspected crawl space conditions, including vapor barrier integrity, foundation walls, and available space for ductwork routing and equipment placement. Documented existing plumbing infrastructure and floor joist configuration to determine optimal equipment positioning and clearance requirements. Evaluated exterior foundation areas and basement window well accessibility for potential condenser unit placement and refrigerant line routing. Provided detailed estimate for full system upgrade including new furnace and central air conditioning installation to modernize heating and cooling capabilities.

Completed full HVAC system installation in basement mechanical room, including 110,000 BTU Lennox furnace with left-side configuration and 4-ton air conditioning unit. Installed PVC venting system with proper vertical exhaust piping, connected humidifier to furnace, established all electrical connections, and integrated new equipment with existing ductwork and air distribution plenums. All mechanical permits obtained prior to installation, system fully reconnected and operational upon completion.

Completed full HVAC system installation including a 70,000 BTU furnace and 3-ton air conditioning unit with rear discharge configuration. The outdoor condenser was positioned on a concrete pad with proper base support against the exterior wall, and all refrigerant lines and electrical connections were established. Interior mechanical components were installed with condensate drainage routed to existing floor drain, all necessary permits obtained, and system reconnected and tested for proper operation.

Performed diagnostic evaluation on 13-year-old Generac standby generator experiencing voltage irregularities causing lights to flicker during operation. Assessed electrical output, transfer switch operation, and load distribution to identify source of voltage fluctuations. Documented equipment condition and provided replacement recommendations based on age and performance issues.

Successfully completed installation of a 2-ton air conditioning system with evaporator coil at rear of residence. Positioned outdoor condensing unit on pad against exterior siding with proper refrigerant line routing and electrical disconnect installation. Indoor evaporator coil installed in basement mechanical room with copper refrigerant lines, condensate drain piping, and electrical connections to existing furnace system. System properly charged, tested for proper operation, and all mechanical and air conditioning permits obtained prior to installation.

Completed annual heating and cooling maintenance inspection on residential gas furnace system. Performed comprehensive evaluation of all internal components including gas valve assembly, heat exchanger, blower motor, control board, and electrical connections. Inspected PVC venting and condensate drain lines for proper installation and security. Verified all wire connections and control board functionality. Documented system condition through detailed photography of interior components with access panels removed. All components found operating within normal parameters with no immediate service needs identified.

Completed return service call to replace failed electrical components on residential air conditioning system. Replaced defective contactor, capacitor, and circuit breaker to restore proper system operation. All replacement parts installed to manufacturer specifications. System tested and verified operational following component replacement.

Responded to service call for 20+ year old outdoor air conditioning unit with suspected refrigerant leak in coil. Upon arrival, performed visual inspection of condenser unit positioned against building exterior. Noted unit showing significant age-related wear with dirty condenser coils containing accumulated debris, cobwebs, and fibrous material between fins. Information plate on unit panel heavily weathered with faded specifications. Assessed system for refrigerant leak as reported, examining evaporator coil condition and checking for signs of refrigerant loss. Unit requires thorough coil cleaning to restore proper airflow and heat transfer efficiency before further diagnostics can determine extent of refrigerant system issues.

Responded to no cooling complaint on 4-year-old Lennox system. Upon arrival, found ice buildup on refrigerant lines at evaporator coil connection, indicating restricted airflow or low refrigerant charge. Thermostat was calling for cooling and indoor blower was operating, but minimal air delivery through supply registers confirmed airflow restriction. Performed system diagnostics using inspection camera to assess evaporator coil condition and verified blower operation. Identified frozen evaporator coil as primary issue preventing proper cooling. System shut down to allow coil to thaw completely before proceeding with further diagnostics to determine root cause of icing condition, whether due to dirty filter, blocked return air, low refrigerant charge, or failed blower motor capacitor.

Conducted site consultation with carpenter to assess exterior siding removal requirements for upcoming electrical work. Documented current construction phase showing house wrap installation, window weatherproofing, and exposed framing, and inspected existing electrical panel configuration with labeled circuit breakers to determine integration points for planned fixture and outlet installations.

Performed scheduled maintenance on residential split system air conditioning unit. Inspected indoor evaporator coil assembly in attic space and outdoor condensing unit, verifying proper operation of all components. Checked refrigerant lines, condensate drainage system, electrical connections, and confirmed system is operating within normal parameters for continued reliable cooling performance.

Completed scheduled Air Care Cooling maintenance on Lennox outdoor condensing unit. Performed comprehensive inspection of equipment, verified proper operation of all components, and documented unit condition with photos showing clean, well-maintained exterior and properly functioning fan assembly.

Completed HVAC estimate for replacement of aging air conditioning system experiencing inadequate cooling performance. Assessed existing basement-mounted furnace and outdoor condenser unit, documented current equipment condition and installation configuration including electrical connections, refrigerant lines, and condensate drainage. Provided comprehensive replacement quote for new cooling system to restore proper climate control functionality.

Completed scheduled preventative maintenance on residential central air conditioning system. Performed comprehensive inspection of HVAC equipment in basement utility area, including examination of furnace unit, ductwork, and associated components. Replaced air filter with new pleated media filter to ensure proper airflow and system efficiency.

Completed full system replacement estimate for two aging HVAC units requiring immediate replacement: a 3.5-ton AC with attic-mounted air handler and a 4-ton AC with coil system, both approximately 16 years old. Performed comprehensive assessment of existing equipment, measured ductwork dimensions and clearances, evaluated refrigerant line routing, and documented current system configuration to provide accurate replacement specifications for 17 SEER equipment upgrades.