HVAC, Water Heater & Electrical Services in Grand Ledge, MI

Performed annual cooling maintenance on Bryant outdoor condensing unit. Measured and recorded electrical parameters showing 36.37 amps and 232.5 volts, confirming proper system operation. Inspected condenser coil, fan assembly, and surrounding area, noting debris accumulation around unit base that was addressed during service.

Completed annual cooling maintenance on ACM unit. Performed comprehensive system inspection, tested electrical components and recorded amperage readings using clamp meter, verified capacitor values with multimeter showing 42.72 MFD reading. All measurements within manufacturer specifications, unit operating properly with no deficiencies noted.

Completed annual cooling maintenance on residential HVAC system. Performed comprehensive inspection of equipment, verified electrical components and capacitor readings using digital multimeter, replaced furnace filters, and documented unit specifications and serial number information. All systems operating within normal parameters upon completion.

Successfully completed full HVAC system installation including new air conditioning condenser unit and evaporator coil. Installed outdoor condenser unit on rubber isolation pad at rear of residence with proper clearances, mounted electrical disconnect box, and established new dedicated electrical circuit per code requirements. Interior work included evaporator coil installation integrated with existing furnace system, connected refrigerant lines with proper insulation, completed all electrical connections and control wiring, and verified proper gas line connections and safety controls. All mechanical, electrical, and air conditioning permits were obtained and system was tested for proper operation, refrigerant charge, airflow, and safety controls prior to final inspection.

Provided comprehensive estimate for complete furnace and air conditioning system replacement in basement mechanical room. Existing 18-year-old equipment is non-operational and requires full replacement under BOGO promotion terms. Customer is an Air Care Member requiring updated HVAC solution for residential heating and cooling needs.

Responded to service call for blank thermostat display. Upon arrival, performed comprehensive annual heating checkup on furnace system as requested. Diagnosed thermostat failure and replaced unit with new thermostat, restoring proper system control and display functionality. Inspected furnace interior components, including control board, wiring harness connections, and safety controls—all found to be operational. Examined condensate drain pan and noted moisture accumulation with visible corrosion on metal housing components, typical of unit age and normal condensate drainage. Replaced furnace air filter to maintain proper airflow and system efficiency. Verified all electrical connections secure, tested system operation through complete heating cycle, and confirmed thermostat communication with furnace control board. System now operating properly with full thermostat functionality restored.

Conducted site assessment for new 3-zone mini-split system installation. Evaluated interior spaces including nursery with board-and-batten paneling and workshop area to determine optimal placement for indoor air handler units. Documented wall construction, ceiling conditions, and spatial considerations for equipment mounting and refrigerant line routing. Provided comprehensive estimate for complete ductless HVAC system installation with three zones to accommodate residential heating and cooling needs.

Completed full HVAC system installation including a 70,000 BTU furnace and 2.5-ton air conditioning unit in attic space with left-side configuration. Installed new air handler with flexible ductwork connections, reconnected existing electrical service, and mounted Sensi programmable digital thermostat on interior wall. System commissioned and tested for proper operation with all mechanical permits obtained prior to installation.

Completed spring AC tune-up on Lennox system with 2-year warranty coverage remaining through April 2028. Performed comprehensive maintenance inspection of indoor air handler unit in basement, verifying proper operation of furnace components, condensate drainage system, and refrigerant lines. Inspected outdoor condenser unit and documented significant accumulation of dirt and debris on mesh panel and coil surfaces requiring attention. System currently operating properly with all components functioning as designed.

Completed annual cooling maintenance on residential split system. Inspected outdoor condenser unit and indoor furnace/air handler in basement mechanical room. Verified proper air filter installation and condition. Performed standard ACM protocol including visual inspection of all accessible components, ductwork connections, and refrigerant lines. System operational and ready for cooling season.

Completed scheduled Air Care Cooling maintenance on outdoor HVAC system. Replaced heavily soiled and discolored air filter showing significant dust and debris accumulation. Inspected condenser unit exterior, confirmed proper fan grille condition, and verified unit positioning on concrete pad remains stable.

Successfully installed a complete 2.5-ton air conditioning system with matching evaporator coil at the rear of the property. The outdoor condenser unit was positioned on a stable pad against the building exterior with proper electrical disconnect and conduit routing, while the indoor coil was installed in the existing structure with appropriate refrigerant line connections and drainage piping. All mechanical and electrical connections were completed per code requirements, the system was charged, tested, and verified operational.

Conducted comprehensive assessment of existing HVAC system for replacement estimate, evaluating a 31-year-old air conditioning unit and 20-year-old furnace system located in basement utility area. Documented current equipment conditions through detailed photography, noting age-related deterioration and wear patterns on both heating and cooling components. Provided pricing options for both combined system replacement and separate unit replacement to allow comparison of installation approaches based on equipment lifecycle and operational efficiency considerations.

Conducted on-site evaluation for mini-split system installation in residential property. Assessed bedroom and living room areas to determine optimal placement for indoor air handling units, evaluating wall space, electrical requirements, and airflow patterns. Documented existing conditions and room layouts to develop comprehensive installation proposal for ductless HVAC system to meet customer's timeline of replacement within the next couple weeks.

Completed comprehensive Air Care Heating and Cooling maintenance on Luxaire furnace system. Performed thorough inspection of all heating components including gas valve assembly, blower motor, control board, and electrical connections. Verified proper operation of draft inducer, inspected heat exchanger, and confirmed all safety controls functioning correctly. Checked and tested blower motor assembly and verified proper airflow. Inspected all wiring connections, control board operation, and safety interlocks. Examined water heater connections and associated plumbing in mechanical room. All equipment operating within manufacturer specifications with no deficiencies noted. System ready for continued reliable operation.

Provided comprehensive estimate for complete HVAC system replacement including new air conditioning unit and natural gas furnace to be installed in existing location between bedroom and kitchen. Evaluated current vertical furnace installation in closet space, assessed existing ductwork configuration and electrical panel capacity to determine equipment specifications and installation requirements for new system.

Conducted full system estimate for residential HVAC replacement. Evaluated existing 16-year-old air conditioning unit positioned on exterior pad with significant debris accumulation and deteriorated mounting surface. Unit features top-mounted A-frame condenser coil configuration showing signs of weathering and outdoor exposure. Customer recently had furnace installation completed and is seeking air conditioning replacement within the next couple weeks to complete full system upgrade. Assessed installation site conditions, equipment access, electrical service routing, and clearance requirements. Documented current equipment specifications and surrounding area conditions including compromised pad surface and accumulated organic debris requiring attention during replacement. Provided comprehensive estimate for new air conditioning system installation to match recently installed furnace and restore complete climate control functionality.

Completed scheduled maintenance on air handling unit. Performed comprehensive inspection of blower motor assembly, ductwork connections, gas valve, heat exchanger, and electrical wiring systems. All components found operating within normal parameters with no deficiencies noted. Unit tested and left in proper working condition.

Completed annual cooling maintenance on HVAC system. Performed comprehensive inspection of furnace unit with access panel removed to evaluate internal components including blower motor assembly, electrical connections, and control board. Verified proper electrical readings using digital multimeter, measuring 67.9 on system diagnostics. Inspected all wire connections including orange, blue, green, white, and red conductor pathways for secure terminations and signs of wear. Evaluated control board functionality and verified all safety labels present and legible. System operational and ready for cooling season.

Completed annual cooling maintenance on Lennox outdoor condensing unit. Performed comprehensive system inspection, cleaned condenser coils, checked refrigerant levels and electrical connections, verified proper airflow through fan assembly, and confirmed unit operational status with no deficiencies noted.