HVAC, Electrical & Water Heaters in DeWitt, MI

Provided comprehensive estimate for complete HVAC system replacement of 30-year-old air conditioning unit and furnace. Existing AC unit completely non-operational and both systems at end of service life. Assessed current equipment configuration including furnace with humidifier, ductwork, condensate drainage system, and electrical panel connections to determine replacement specifications and installation requirements for expedited system changeover.

Responded to service call for non-cooling air conditioning system affecting entire residence. Evaluated 20-year-old HVAC system including existing Luxaire furnace, air handler with Space-gard air cleaner, and outdoor condensing unit. Documented current equipment configuration, ductwork layout, and basement installation setup with photographic evidence. Provided comprehensive replacement estimate options for aging air conditioning system that had reached end of serviceable life expectancy.

Responded to no cooling call on a three-year-old residential air conditioning system. Upon arrival, verified the outdoor condenser unit was not operating and confirmed no power to the system. Inspected the exterior disconnect box and electrical connections, noting vegetation growth around the base of the condenser unit that had accumulated over time. Tested electrical components, identified the issue, and restored power to the system. Verified proper operation of the condenser fan and compressor, confirmed adequate airflow through the unit, and ensured the system cycled normally. Cleared debris and vegetation from around the condenser to maintain proper clearance for optimal performance and future serviceability.

Performed annual preventative maintenance and system checkup on 14-year-old Bryant central air conditioning unit. Connected refrigerant manifold gauge set to outdoor condenser unit to measure and verify system pressures and refrigerant charge levels. All gauges indicated proper operating pressures within manufacturer specifications. Inspected condenser coil fins, fan assembly, and electrical connections. System confirmed operational with proper heating and cooling capability maintained.

Completed comprehensive tune-up service on 3-year-old Bryant furnace and Lennox CX39-24B-6F-20 condensing unit. Performed standard maintenance inspection including filter check, electrical connections verification, condensate drain system evaluation, and coil assessment on both indoor and outdoor equipment. All components found operating within normal parameters with no deficiencies noted.

Responded to no cooling or heating call with blank thermostat screen on 2021 basement-located system. Upon inspection, diagnosed failed thermostat requiring replacement. Installed new thermostat, restored power, verified proper communication with HVAC equipment, and confirmed system operation in both heating and cooling modes. Tested temperature readings and ensured all functions were operational before departure.

Responded to no cooling complaint on Lennox air conditioning system. Upon arrival, inspected outdoor condenser unit and found failed contactor preventing compressor operation. Contactor contacts were pitted and burned, unable to close circuit when called for cooling. Replaced defective contactor with new unit, verified proper electrical connections, and tested system operation. Unit cycled on successfully with compressor engaging properly. Confirmed adequate airflow through condenser coil and normal operating pressures. System restored to full cooling capacity.

Completed annual cooling maintenance on residential HVAC system. Performed comprehensive inspection of furnace, air handler, and associated components including refrigerant lines, condensate drainage system, and ductwork. Replaced air filter, verified proper operation of all equipment, and documented system condition with photos.

Conducted on-site assessment for whole-home humidifier installation in a 2,300 square foot two-story colonial residence. Evaluated existing HVAC system in basement utility area, including ductwork configuration, current air filtration setup, and available connection points for humidifier integration with copper water supply lines. Documented equipment layout and provided comprehensive estimate for humidifier installation compatible with existing forced-air heating system.

Completed comprehensive air conditioning tune-up on outdoor condensing unit. Performed standard preventative maintenance procedures including inspection of electrical connections, refrigerant level verification, condenser coil cleaning, and operational testing of all components. Unit operating within normal parameters upon completion.

Successfully completed installation of a 2-ton air conditioning system with evaporator coil, including establishment of a new dedicated electrical circuit with disconnect box and proper conduit routing. The condensing unit was positioned on a level pad against the exterior wall with left-side configuration, and all mechanical and electrical permits were obtained prior to installation. System was commissioned, tested for proper operation, and documentation was finalized upon completion.

Completed full HVAC system installation including a 90,000 BTU high-efficiency furnace with humidifier and 3.5-ton air conditioning unit with rear discharge configuration. Installed white PVC venting for furnace exhaust and intake, ran electrical conduit and disconnect to outdoor condenser unit positioned on gravel pad, and reconnected all ductwork to existing system. All equipment installed per manufacturer specifications with proper clearances, permits obtained for mechanical work, and system tested for proper operation upon completion.

Performed comprehensive preventive maintenance tune-up on residential outdoor air conditioning condenser unit. Completed standard system inspection, cleaning, and performance verification procedures to ensure optimal operation for the cooling season. Unit operational and ready for service upon completion.

Responded to emergency service call for reported gas odor from 3-year-old furnace in basement that had been shut down for safety. Performed comprehensive leak detection inspection using electronic refrigerant/gas leak detector on furnace cabinet, heat exchanger, gas valve assembly, and all gas piping connections. Removed front access panel and thoroughly inspected internal components including blower motor, wiring harnesses, burner assembly, and flue piping. Checked all PVC vent pipe connections and condensate drain trap for proper seal integrity. Verified gas supply line connections and flexible conduit routing. All components inspected showed no evidence of gas leaks or combustion issues. Unit remains under parts and labor warranty coverage.

Completed annual cooling maintenance on Bryant outdoor condensing unit. Performed comprehensive system inspection, verified refrigerant lines and electrical disconnect in proper working condition, confirmed unit operational with no deficiencies noted. Equipment found clean and functioning normally on rock pad foundation with proper drainage.

Completed routine AHC maintenance on furnace and air conditioning system, including replacement of air filters and evaporator pads as needed. Inspected and serviced HVAC components, flexible ductwork connections, and vibration isolation mounting hardware to ensure proper system operation and efficiency for both heating and cooling functions.

Completed annual preventative maintenance on residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, including visual assessment of cabinet condition, fan operation, and refrigerant line connections. Verified proper unit placement on concrete pad and checked electrical connections at exterior wall penetration. Tested system operation and documented equipment condition with photographic records. All components found operating within normal parameters with no immediate service needs identified.

Completed comprehensive furnace tune-up including inspection of all major components, burner assembly, heat exchanger, blower motor, and safety controls. Verified proper operation of intake and exhaust venting system, checked condensate drainage, and confirmed unit is operating within manufacturer specifications.

Completed full HVAC system installation consisting of one 70,000 BTU Lennox furnace installed in attic space on properly constructed wooden platform with vertical and horizontal ductwork connections, plus two 2-ton air conditioning units for dual-zone cooling. Performed mechanical and electrical rough-in work, installed two new dedicated electrical circuits to code for equipment operation, and positioned second furnace unit in basement utility area with appropriate condensate drainage, PVC venting, and metal supply ductwork. All units secured on stable platforms, ductwork properly sealed and insulated, electrical connections completed, and systems tested for proper operation.

Completed routine maintenance on residential forced air furnace and air conditioning system. Performed comprehensive AC tune-up including inspection of blower motor assembly, gas valve components, electrical connections, and control wiring. Verified proper operation of all mechanical and electrical components within the air handler unit. Inspected ductwork connections, PVC condensate lines, and electrical panel connections. All systems tested and confirmed operating within normal parameters with no deficiencies noted at time of service.