HVAC Repair & Electrical Services in Okemos, MI

Completed comprehensive ComfortGuard Maintenance Package on 5-year-old forced air furnace and air conditioning system as part of ongoing five-year maintenance program following 2021 installation. Performed full AC tune-up including inspection of all mechanical components, refrigerant level verification, electrical connection testing, and condenser coil cleaning. Conducted furnace maintenance including burner inspection, heat exchanger examination, blower motor lubrication, air filter replacement, and safety control verification. Verified Sensi programmable thermostat operation and calibration at 72°F setpoint with proper heat and cool mode functionality. Inspected intake and exhaust PVC venting for proper clearance and secure connections. Tested system startup and shutdown sequences for both heating and cooling modes. All equipment operating within manufacturer specifications with no issues identified or repairs required.

Completed comprehensive ComfortGuard maintenance service on residential HVAC system operating under 5-year warranty plan. Performed full tune-up on air conditioning condenser unit and furnace system, both confirmed in proper working condition. Outdoor condenser unit showed significant accumulation of dirt, dust, and debris on condenser fins and coils, which was thoroughly cleaned to restore optimal airflow and heat transfer efficiency. Inspected fan motor assembly, grille, and mounting pad for proper operation and stability. Verified refrigerant levels, electrical connections, and overall system performance. All components tested and functioning within normal parameters upon service completion.

Installed 26RCA generator with 200-amp transfer switch and completed all associated electrical connections. Addressed previous failed inspections by performing comprehensive gas pressure test, locating and repairing system leak, and verifying system holds proper pressure with gauge readings confirming successful repair. Coordinated utility disconnect and reconnect services, requested required electrical permits, and prepared installation for scheduled electrical inspection.

Completed installation of 20kW standby generator system including electrical and mechanical integration. Installed new gas piping to fuel source, integrated automatic transfer switch with existing 200-amp electrical service, and obtained mechanical and electrical permits for generator installation. System tested and operational upon completion.

Conducted on-site assessment for non-functioning natural draft water heater replacement in residential property. Customer requested upgrade to 75-gallon capacity unit, requiring evaluation of existing installation space, venting configuration, and clearance requirements. Documented current equipment dimensions and surrounding utility infrastructure including ductwork, plumbing connections, and structural constraints to determine feasibility of larger capacity installation.

Completed comprehensive annual maintenance on a four-year-old furnace and air conditioning system under ComfortGuard Maintenance Package. Performed full AC tune-up including refrigerant level verification, condenser coil inspection and cleaning, electrical connection testing, and airflow measurements. Inspected air handler unit, verified proper filter installation, tested thermostat operation and calibration on ecobee digital control system, and confirmed all safety controls functioning within manufacturer specifications. Both heating and cooling systems operating efficiently with no deficiencies noted; all components passed inspection criteria.

Installed pressure gauges on generator system plumbing assembly in preparation for scheduled inspection. Gauges were mounted and connected to pipe assembly with appropriate fittings and valves, with equipment positioned and secured among landscaping. Coordinated pickup timing with property owner and ensured all monitoring equipment was operational prior to inspection window.

Performed comprehensive AC tune-up on residential split system with outdoor condenser unit and Carrier indoor air handler/furnace combination. Inspected outdoor condenser unit showing age-related weathering and dirt accumulation; cleaned unit exterior and verified fan operation through protective guard. Evaluated indoor evaporator coil mounted above furnace, noting visible condensation indicating active cooling cycle. Checked refrigerant levels and system pressures to determine if refrigerant charge was adequate; found system operating within manufacturer specifications with no refrigerant leak detected or addition required. Verified proper condensate drainage through PVC drain lines, inspected electrical connections, and confirmed system cycling properly. All components functioning as designed with no immediate service needs identified beyond routine maintenance completed.

Conducted electrical estimate for new whole home generator installation at manufactured residence. Evaluated existing electrical panel configuration, which contains dual columns of circuit breakers with main breaker positioned at top right, numbered circuits 1-41, and adequate capacity for generator integration. Assessed kitchen area and overall electrical load requirements to determine proper generator sizing and transfer switch specifications for seamless backup power integration with current electrical system.

Completed annual heating maintenance on AHU system. Performed inspection of internal components including blower motor, gas valves, electrical connections, and heat exchanger assembly. Replaced MERV 11 air filter (HCF16-11). Inspected outdoor condenser unit which exhibited heavy accumulation of dirt and debris on exterior coil fins restricting airflow. All mechanical and electrical components within furnace compartment were visually inspected and found to be in operational condition with proper wire connections and gas line fittings secure.

Responded to customer concern regarding non-functioning humidifier system. Performed diagnostic inspection of residential HVAC system including Trane furnace and associated IAQ equipment. Inspected humidifier unit for proper water supply, solenoid operation, and pad condition. Verified humidistat settings and control wiring connections. Checked water panel media for mineral buildup or deterioration that could prevent proper moisture distribution. Documented system configuration and current equipment condition with photos for service records.

Responded to callback for no airflow and thermostat not controlling system. Performed diagnostic evaluation of air conditioning system and Copeland scroll compressor using CoreSense diagnostic tool. Verified outdoor condensing unit operation, inspected control panel components, and tested system functionality. Previous service history indicated furnace board and thermostat replacement had been completed. Confirmed system operational status and documented equipment condition with photographic records of outdoor unit installation and control panel diagnostics.

Conducted comprehensive estimate for two-system installation: cold-climate ductless heat pump for 638 sq. ft. three-car garage with 12'4" ceilings, and whole-house ERV integration for 5,000 sq. ft. residence with existing Goodman M9S96 furnace. Performed site assessment including evaluation of garage insulation conditions, air leakage potential, and electrical panel capacity for additional circuits. Documented existing electrical infrastructure and workspace areas to determine proper load calculations rather than simplified square footage sizing methods. Evaluated indoor air quality concerns with elevated CO₂ levels measuring 1,500-2,000 ppm in main living space with five occupants, assessed compatibility of Panasonic BalancedHome Elite Plus 210 ERV unit for application, and reviewed existing four-year-old basement ductwork for integration requirements. Proposal will include Manual J load calculations for garage, insulation upgrade recommendations, electrical requirements for heat pump

Completed routine Air Care Cooling preventive maintenance on residential HVAC system. Inspected Goodman furnace model EL297UH110XU60UC-04 and outdoor condenser unit, verified proper operation of all components, documented equipment condition with photos, and confirmed system is functioning within normal parameters.

Completed comprehensive AC tune-up on 10-year-old system currently operating properly. Performed standard maintenance protocol including inspection of air handler unit in attic space, verified proper operation of all components, checked refrigerant levels, inspected ductwork and insulation, and confirmed Nest thermostat programming and functionality with setpoint at 67°F. System tested and left in optimal working condition.

Conducted on-site estimate for new Mitsubishi mini split heat pump installation in residential property without existing central air or ductwork. Evaluated three bedrooms for system design, with proposed air handler placement in attic to serve two bedrooms. Assessed electrical requirements, exterior mounting locations for outdoor unit, and refrigerant line routing through structure. Photographed installation areas including bedroom spaces to document wall conditions, window placements, and interior layout for equipment sizing and placement planning. Confirmed existing boiler system provides adequate heating and domestic hot water with no reported operational issues. Provided customer with equipment options and installation specifications for ductless heat pump system to deliver year-round climate control.

Conducted comprehensive site assessment for backup generator installation at 3,700 square foot colonial residence requiring updated estimate from previous 2022 evaluation. Evaluated existing electrical service entrance equipment, including main meter base, electrical panel, and associated conduit routing on exterior wall to determine optimal integration point for automatic transfer switch and generator connection. Documented current electrical panel configuration with dual columns of circuit breakers to assess load requirements and determine appropriate generator sizing for whole-house or critical circuits backup power solution. Photographed existing utility infrastructure and service entrance components to provide accurate specifications for generator system design and installation planning.

Completed full HVAC system installation including a 90,000 BTU gas furnace with humidifier and 3-ton air conditioning system with evaporator coil. Installed new air handler unit in basement with proper condensate drainage lines and ductwork connections, and positioned outdoor condenser unit on concrete pad with electrical reconnection. All equipment installed per manufacturer specifications and permit requirements, with system tested and operational upon completion.

Provided comprehensive estimate for replacement of 22-year-old furnace and air conditioning system located in basement, with current A/C unit experiencing short cycling issues. Assessed existing equipment layout, electrical service panel capacity, and available space for new installation including proper clearances for ductwork and refrigerant lines. Documented site conditions and utility connections to prepare detailed proposal for complete HVAC system replacement with natural gas furnace and new condensing unit.

Responded to service call for air conditioning system not cooling due to water leak from cracked condensate leak detector. Upon inspection, found the condensate pump assembly experiencing leakage at the detector connection, causing water damage to surrounding floor area and preventing proper system operation. Replaced faulty leak detector component and condensate pump assembly, reconnected drainage lines with proper PVC fittings, tested system for proper drainage flow, and verified air conditioning unit returned to normal cooling operation with no further leakage detected.